Intelix VGA2-UHR Manuel d'utilisateur télécharger pdf

8001 Terrace Ave.

Suite #201

Middleton, WI 53562

Phone: 608-831-0880

Toll-Free: 866-4-MATMIX

Fax: 608-831-1833

VGA2-UHR Installation Guide

The Intelix VGA2-UHR extends a computer video signal

over a single twisted pair cable. The VGA2-UHR supports

computer video resolutions up to WUXGA (1920 x 1200) to

a maximum distance of 168m (550’).

Dipswitches on the Transmit balun allow for Built-in EDID

presets of common resolutions (1024x768 and 1280x800)

and EDID copy mode. In EDID copy mode the Receive

balun transmits the EDID of the remote display back to the

Transmit balun for custom EDID storage.

The Receive balun has trim pots for skew compensation

and brightness.

Dipswitches

Transmiter (VGA2-UHR-S) – EDID Modes

Function Description

Down

EDID Copy Mode On

Down

1280 x 800 (WXGA)

1024 x 768 (XGA)

Reciever (VGA2-UHR-R) – Skew Adjustment

Adjust the trim pot to match the length of the UTP.

Twisted Pair

Wiring - Use

T568B wiring for

Cat5e/6

connection

between send

and receive

units.

Troubleshooting

Symptom

Possible Solutions

No signal

Active LED is off

Verify that both ends of the twisted pair cables use

T568B crimp pattern.

Verify VGA cables and source and destination VGA

ports are operational.

No signal

Verify the power supply is connected to the send

balun.

Verify the power LEDs on both the send and

receive units are brightly illuminated.

Unusual colors or

blurry video

Adjust for the length of you UTP cable.

Adjust the brightness on the receive balun.

No EDID copy

Long cable lengths will cause EDID copy to fail.

Copy the EDID with a short cable then install.

Installation Instructions

1. Turn off power and disconnect VGA cables

from computer and display.

2. Connect a VGA cable between the display and

the receiver (VGA2-UHR-R).

3. Connect twisted pair cable between the

transmitter (VGA2-UHR-S) and the receiver

(VGA2-UHR-R). Ensure T568B straight-thru

wiring.

4. Connect the included power supply to the

transmitter.

5. Connect a VGA cable between the computer

and the transmitter (VGA2-UHR-S).

6. Power on attached audio/video devices.

EDID Copy Instructions

1. Set dipswitch 2 down.

2. Follow “Installation Instructions”.

3. Press the EDID copy button.

4. Wait for flashing LED and a “click”

noise. EDID copy is completed.

*Note: The VGA2-UHR will only change EDID

modes after completely disconnecting both

power and VGA cabling.

1 2

Résumé du contenu

Page 1 - VGA2-UHR Installation Guide

8001 Terrace Ave. Suite #201 Middleton, WI 53562 Phone:

Page 2 - Technical Specifications

8001 Terrace Ave. Suite #201 Middleton, WI 53562 Phone:

Commentaires sur ces manuels

Pas de commentaire

Intelix VGA2-UHR Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Matériel Intelix VGA2-UHR. Intelix VGA2-UHR User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Matériel Intelix VGA2-UHR